Desktop Barcode Scanner

Product Information

Model: NLS-FR4060
Product Category: Desktop Barcode Scanner
Data type: 2D Bar Codes
Reading Mode:
Interface: RS-232, USB, PS/2
Wireless: None


Quick to Switch Mode

The Scan Mode Switch at the top of the scanner allows users to swiftly toggle between the Regular and Screen modes.

Superior Motion Tolerance

Exceptional motion tolerance (2.5m/s) and large FOV (46°) enhance user experience.

IP50-rated Sealing

An IP50-rated seal renders the scanner impervious to dust, water and other contaminant.

Superb Reading Performance

Armed with Newland’s fifth-generation of  technology, the scanner is capable of reading 1D as well as high-volume 2D barcodes on the screen covered with protective film.

IR Trigger

The IR sensor in the scanner enables speedy capture of barcodes presented to it, markedly increasing throughput and productivity.



Image Sensor

752*480 CMOS


2D          PDF417, QR Code, Data Matrix, Chinese Sensible Code

1D          EAN-13, EAN-8, UPC-A, UPC-E, ISSN, ISBN, Codabar,
Code 128, Code 93, ITF-6, ITF-14, Interleaved 2 of 5,
Industrial 2 of 5, Standard 2 of 5, Matrix 2 of 5, GS1 Databar, Code 39, Code 11, MSI-Plessey, Plessey, etc.



Typical Depth of Field

Code 39     10-100mm (5mil)

UPC-A       0-250mm (13mil)

PDF 417     0-80mm (6.67mil)

Data Matrix  10-90mm (10mil)

QR Code     10-150mm (15mil)

Motion Tolerance


Scan Angle

Pitch        ±60°@ 0°Roll and 0° Skew

Roll         ±360°@ 0°Pitch and 0° Skew

Skew        ±55°@ 0°Roll and 0° Pitch

Symbol Contrast



RS-232, USB


Dimensions (L×W×H)





Beep, LED indicator


Operating   150mA

Standby     120mA


Operating Temperature


Storage Temperature



5%~95% (non-condensing)


±14 kV(air discharge),±8 kV(direct discharge)


1.2m drops to concrete (for six sides, one drop per side)




FCC Part15 Class B,CE EMC Class B



USB         Used to connect the scanner to a host device.
RS-232      Equipped with a power connector;used to connect the scanner to a host device.

Power Adapter

Used to provide power for the scanner.
Output: DC5V,1.5A; Input: AC100~240V, 50~60Hz


**Test conditions:

Code 39, 3 Bytes; Resolution=10mil; W:N=2.5:1; PCS=0.8; Barcode Height=40mm; Scan Distance=210mm, T=23℃,  Illumination= 200 LUX

*Specifications are subject to change without notice*

  Document Name Size Document Type
1 NLS-FR4060 Datasheet 239K Datasheet
2 NLS-FR4060 User_Guide 2138K User_Guide

1. How to confirm the types of your equipment, X+? X? or other type?
A. X+ type(EM2027 series, last number of serial number is "X+"), supported interface types: USB-DataPipe, USB Com Port Emuation, HID-KBW,RS232.
X type(EM2100 series,last number of serial Number is "X"), supported interface types: USB-DataPipe, USB Com Port Emuation, HID-KBW,RS232.

2. How to confirm whether the driver has been installed successfully?
A. First, confirm the equipment had connected to PC and the equipment operating normally.
Open: Control Panel> Device Manager> Universal Serial Bus Controller,
 If there is "Newland USB Datapipe to series Device" said connection is "USB Com Port Emuation"--COM.
 If there is "Newland USB DataPipe Device" said connection is "USB-DataPipe".
 If there is yellow "!" before the equipment, delete the equipment, and then scan detection hardware changes,  Wait for the system to automatically install the new drivers finished.

3. Whether it is necessary upgrade the driver of USB-Datapipe from the old version to the new v1.2 USB driver (vcomctrl v1.2.exe)?
A. The new driver support USB Interface of X+ : USB-DataPipe/ USB Com Port Emuation/HID-KBW. If the users of X series, had developed their own application through the USB SDK, recommendations are not updated to the latest driver.

4. If you have installed v1.2 USB driver, how to connect by USB-Datapipe?
A. If your equipment is X+ series, read the set code of USB-Datapipe.(You can download The Manual of Settings Code free from this website.) If your equipment is X series, first you should close USB to COM serve, open Control Panel> Tools> Services, find "Bulk to Serial service", select properties: select stop, Startup Type: Manual.

5. After installed the new driver, how to find out the COM port corresponding to the USB Com Port Emuation?
A. Open Start> all the procedures>vcomctrl>vcomctrl, you can find the number of the COM port there.

6. Why QuickSet can not connect the equipment through USB after installed v1.2 driver?
A. Confirm FAQ-1 driver has installed correctly --> Check out the number of COM port of FAQ-4 --> Confirmed equipment has been launched. Open the Quickset, select the right COM port,manual detection. If the detection failed, you can choose one of the following ways to solve the problem:

i.Check out whether swich to HID-KBW and have set Non-HID-KBW when read The Manual of Settings Code. Change and connect it again.

ii. If it connect through COM before, open "File>PC comm... > USB>OK" in Quickset, try whether it work.

iii. Close Quickset, close connection then open Control Panel> Tools> Services, find "Bulk to Serial service", select properties: select stop, and then start it again. Connect the equipment, open Quickset, try connection through COM.

iv. Close Quickset, close connection. Reboot the equipment, open Quickset, connect it again.

  Document Name Size Document Type
1 signed_driver for 7K Driver
2 16.7M Driver
3 OPOS Newland Scanner 1257K Driver


USB Cable 
Communication with PC 

RS232 Cable 
Communication with PC 

Ps2 Cable 
Communication with PC 


Premier Wen Jiabao visiting Newland
More »
Newland North America Founded
On July 25, 2008, the Ministry of Commerce of the People’s Republic of China granted the request of Fujian Newland Auto-ID Tech.Co.,Ltd, to invest in the U.S.

More »
Newland's website was renewed
Our website was renewed in Jul. 2008.

More »